OcÃ© CS9360 Скачать руководство пользователя страница 24

Страница: 24 / 134

CS9350 OPERATION MANUAL

3-24

Step 2:

Press [Power] to switch OFF the printer.



The Power lamp on the operation panel is turned off.

NOTE



If the operation panel is in the following status, the power is ON.



Power] is pressed in.



Power lamp is on (blue).



Press the key once again to switch OFF the power.



The printer starts the procedure to switch the power OFF.



“Power Off” is displayed.

NOTE



If the head height is set to High, “Set Height to Low” is displayed on the operation panel
and the procedure to switch the power OFF stops.

To restart the procedure, return the head height to Low.

4.2.5.2 When returning the print head to the original position



All the lamps on the operation panel and the LCD monitor are switched OFF.



The printer automatically powers OFF.

NOTE



If there is a problem during switching OFF operation, a message is displayed on the
operation panel and the printer may stop operating.

If operation stops, refer to “7 Troubleshooting” and deal with the problem.



After switching OFF the printer, wait for ten seconds or longer to switch it ON again.

Содержание CS9360







































































































































Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды

OcÃ© CS9360, Руководство по эксплуатации

Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды