OcÃ© CS9360 Скачать руководство пользователя страница 21

Страница: 21 / 134

CS9350 OPERATION MANUAL

2-21

(2) Display section

TIP



When an error requiring a restart (fatal malfunction for the printer operation) occurs, all
lamps blink with an alarm.

7.2.3 Error requiring restart

If the error persists even when the malfunction is fixed, contact your local Océ
representative.

N°

Name

Color

Status

Description

Power lamp

Blue

Lamp ON

Power ON.

Lamp blinks • Receiving and analyzing the data.

• Performing media initial operation.

Lamp OFF Power OFF.

Error lamp

Orange

Lamp ON

An error has occurred.
Error content is displayed on the LCD.

Lamp blinks The remaining amount of ink is low.

Lamp OFF There is no error.

High lamp

Green

Lamp ON

The head height is set to High.

Lamp OFF The head height is set to Low.

Low lamp

Green

Lamp ON

The head height is set to Low.

Lamp OFF The head height is set to High.

Take Up lamp

Green

Lamp ON

Media ejection mode is set to “Take-up”.

Lamp OFF Media ejection mode is set to “Off” or “Auto cut”.

Auto Cut lamp

Green

Lamp ON

Media ejection mode is set to “Auto cut”.

Lamp OFF Media ejection mode is set to “Off” or “Take-up”.

Long lamp

Green

Lamp ON

• Cleaning mode is set to Long.
• When the Normal lamp is also on, Cleaning mode is set to Short.

Lamp OFF Cleaning Mode is set to Normal.

Normal lamp

Green

Lamp ON

• Cleaning Mode is set to Normal.
• When the Long lamp is also on, Cleaning mode is set to Short.

Lamp OFF Cleaning Mode is set to Long.

LCD display
section

—

Displays operation status of the printer or an error message.

Содержание CS9360







































































































































Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды

OcÃ© CS9360, Руководство по эксплуатации

Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды