OcÃ© CS9360 Скачать руководство пользователя страница 117

Страница: 117 / 134

CS9350 OPERATION MANUAL

6-117

Step 4:

Press [Cleaning] for at least two seconds.



Start Head cleaning.



“Cleaning **%” is displayed.



After Head cleaning is complete, the operation panel shifts to Normal.

NOTE



If you fail to remove blurs or incompleteness of printing in one Head cleaning, perform
strong cleaning.



If blurs or lacking parts in printed media do not disappear with several times of Head
cleaning, refer to “7 Troubleshooting”, and take appropriate measures.

6.2.4

Cleaning the cleaning wiper

(1) Time for cleaning

Once a week, or when blurs or lacking parts appear on printed media after Head cleaning.

(2) Cleaning procedures

NOTE



Use the cleaning stick to clean the cleaning wiper.

For details of the cleaning stick, refer to “8.3 Options/Supply list”.

Step 1:

If the printer is switched ON, make sure the following.



Printing or other operations are not in progress.



The operation panel display is Normal.

Содержание CS9360







































































































































Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды

OcÃ© CS9360, Руководство по эксплуатации

Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды