OcÃ© CS9360 Скачать руководство пользователя страница 101

Страница: 101 / 134

CS9350 OPERATION MANUAL

6-101

NOTE



Do not replace ink cartridges when the printer is switched OFF.

The remaining ink may not be detected correctly, causing abnormal printing.

Step 2:

Remove the ink cartridge that you want to replace from the slot.

Step 3:

Take out the new ink cartridge from the bag.

NOTE



Open the bag just before attaching the ink cartridge to the ink cartridge slot.

Leaving the ink cartridge with the bag open for a long time may result in abnormal
printing.



Do not insert or remove the ink cartridge more than 10 times.

If the ink cartridge has been removed/inserted more than 10 times, it cannot be used even
though ink remains.

Step 4:

Install a new ink cartridge.

Step 5:

Confirm that the operation panel returns to Normal.

NOTE



If the ink cartridge is replaced during printing, printing resumes.

N°

Name

Ink cartridge

Ink cartridge slots

Содержание CS9360







































































































































Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды

OcÃ© CS9360, Руководство по эксплуатации

Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды