manualshive.com logo in svg

Océ CS9360, Руководство по эксплуатации, Страница: 23 / 134

Поделиться
Скачать
Océ CS9360 Скачать руководство пользователя страница 23

CS9350 OPERATION MANUAL

3-23

Chapter 3  Before using

3.1 

Switching the power ON/OFF

3.1.1 

Switching the power ON

Step 1: 

Press [Power] to switch ON the printer.

Power lamp on the operation panel switches on (blue).

The printer starts initial operation.

When the initial operation is complete, the printer enters Normal.

NOTE

If there is a problem during the initial operation, a message is displayed on the operation 
panel and the printer may stop operating.

 

If operation stops, refer to “7 Troubleshooting” and deal with the problem.

3.1.2 

Switching the power OFF

Step 1: 

Verify the following regarding the operational condition of the product.

Printing or other operations are not in progress.

The operation panel display is Normal.

The Low lamp on the operation panel lights up in green.

NOTE

If the High lamp on the operation panel lights up in green, the head height is set to High.

 

Return the head height to Low before switching the power OFF.

 

4.2.5.2 When returning the print head to the original position

Содержание CS9360







































































































































Отзывы:

Нет отзывов