OcÃ© CS9360 Скачать руководство пользователя страница 102

Страница: 102 / 134

CS9350 OPERATION MANUAL

6-102

(2) Replacing high capacity pack adapter (option)

Step 6:

Confirm that the printer is switched ON.

NOTE



Do not replace high capacity pack adapter when the printer is switched OFF.

The remaining ink may not be detected correctly, causing abnormal printing.

Step 7:

Remove the high capacity pack adapter that you want to replace from the slot.

NOTE



Used ink packs should be put in a plastic bag, etc, and dispose of it in compliance with
local ordinance and instructions of local authorities.

NOTE



Do not remove only ink pack while high capacity pack adapter is installed on the printer.
The information of the remaining smart chip card will be rewritten and the ink pack will not
be usable.

Step 8:

Take out the new ink pack from the bag.

NOTE



Open the bag just before attaching the ink pack to the high capacity pack adapter.

Leaving the ink pack with the bag open for a long time may result in abnormal printing.

Step 9:

Install the ink pack and smart chip card to high capacity pack adapter.

N°

Name

High capacity pack adapter

Ink cartridge slot

Содержание CS9360







































































































































Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды

OcÃ© CS9360, Руководство по эксплуатации

Результаты поиска

Содержание CS9360

Отзывы:

Похожие инструкции для CS9360

Бренды по названию

Популярные бренды