manualshive.com logo in svg

NXP Semiconductors PXN2020, Справочное руководство, Страница: 961 / 1376

Поделиться
Скачать
NXP Semiconductors PXN2020 Скачать руководство пользователя страница 961

Deserial – Serial Peripheral Interface (DSPI)

PXN20 Microcontroller Reference Manual, Rev. 1

Freescale Semiconductor

30-35

30.4.3.5.2

Draining the RX FIFO

Host software or the eDMA controller can remove (pop) entries from the RX FIFO by reading the DSPI 
POP RX FIFO Register (DSPI_POPR). For more information on DSPI_POPR, refer to 

Section 30.3.2.7, 

DSPI POP RX FIFO Register (DSPI_POPR).

 A read of the DSPI_POPR decrements the RX FIFO counter 

by one. Attempts to pop data from an empty RX FIFO are ignored, and the RX FIFO counter remains 
unchanged. The data returned from reading an empty RX FIFO is undetermined.

When the RX FIFO is not empty, the RX FIFO drain flag (RFDF) in the DSPI_SR is set. The RFDF bit is 
cleared when the RX_FIFO is empty and the DMA controller indicates that a read from DSPI_POPR is 
complete or by host software writing a 1 to the RFDF.

30.4.4

Deserial Serial Interface (DSI) Configuration

The DSI configuration supports pin-count reduction by serializing parallel input signals or register bits and 
shifting them out in a SPI-like protocol. The timing and transfer protocol is described in 

Section 30.4.8, 

Transfer Formats.

 The received serial frames are converted to a parallel form (deserialized) and placed on 

the parallel output signals or in a register. 

The various features of the DSI configuration are set in the DSPI_DSICR. For more information on the 
DSPI_DSICR, refer to 

Section 30.3.2.10, DSPI DSI Configuration Register (DSPI_DSICR).

 The DSPI is 

in DSI configuration when the DCONF field in the DSPI_MCR = 0b01.

The DSI frames can be from 4 to 16 bits long, but 4 to 32 bits can be used in the TSB configuration (see 

Section 30.4.10, Timed Serial Bus (TSB),

 for detailed information). 

30.4.4.1

DSI Master Mode

In DSI master mode, the DSPI initiates and controls the DSI transfers. The DSI master has these conditions 
that can initiate a transfer:

•

Continuous

•

Change in data

The two transfer initiation conditions are described in 

Section 30.4.4.5, DSI Transfer Initiation Control.

 

Transfer attributes are set during initialization. The DSICTAS field in the DSPI_DSICR determines which 
DSPI_CTAR

n 

register controls the transfer attributes.

30.4.4.2

DSI Slave Mode

In DSI slave mode, the DSPI responds to transfers initiated by a SPI or DSI bus master. In this mode the 
DSPI does not initiate DSI transfers. Certain transfer attributes such as clock polarity and phase must be 
set for successful communication with a DSI master. The DSI slave mode transfer attributes are set in the 
DSPI_CTAR1.

30.4.4.3

DSI Serialization

In the DSI configuration, 4 to 16 bits can be serialized using two different sources. The TXSS bit in the 
DSPI_DSICR selects between the DSPI DSI Serialization Data Register (DSPI_SDR) and the DSPI DSI 

Содержание PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов