manualshive.com logo in svg

NXP Semiconductors PXN2020, Справочное руководство, Страница: 1144 / 1376

Поделиться
Скачать
NXP Semiconductors PXN2020 Скачать руководство пользователя страница 1144

IEEE 1149.1 Test Access Port Controller (JTAGC)

PXN20 Microcontroller Reference Manual, Rev. 1

35-10

Freescale Semiconductor

35.4.4.1

BYPASS Instruction

BYPASS selects the bypass register, creating a single-bit shift register path between TDI and TDO. 
BYPASS enhances test efficiency by reducing the overall shift path when no test operation of the MCU is 
required. This allows more rapid movement of test data to and from other components on a board that are 
required to perform test functions. While the BYPASS instruction is active, the system logic operates 
normally.

35.4.4.2

ACCESS_AUX_TAP_x Instructions

The ACCESS_AUX_TAP_

x

 instructions allow the Nexus modules on the MCU to take control of the TAP. 

When this instruction is loaded, control of the TAP pins is transferred to the selected auxiliary TAP 
controller. Any data input via TDI and TMS is passed to the selected TAP controller, and any TDO output 
from the selected TAP controller is sent back to the JTAGC to be output on the pins. The JTAGC regains 
control of the JTAG port during the UPDATE-DR state if the PAUSE-DR state was entered. Auxiliary TAP 
controllers are held in RUN-TEST/IDLE while they are inactive.

See 

Section 35.5, e200z0 and e200z6 OnCE Controllers,

 for a block diagram and e200z0 OnCE controller 

register descriptions.

35.4.4.3

CLAMP Instruction

CLAMP allows the state of signals driven from MCU pins to be determined from the boundary scan 
register while the bypass register is selected as the serial path between TDI and TDO. CLAMP enhances 
test efficiency by reducing the overall shift path to a single bit (the bypass register) while conducting an 
EXTEST type of instruction through the boundary scan register. CLAMP also asserts the internal system 
reset for the MCU to force a predictable internal state.

Factory Debug Reserved

1

00010
00011
00100
00101
00110
00111
01001
01010
01100

Intended for factory debug only

Reserved

2

All Other 

Codes

Decoded to select bypass register

1

Intended for factory debug, and not customer use

2

Freescale reserves the right to change the decoding of reserved instruction codes in the future

Table 35-2. JTAG Instructions (continued)

Instruction

Code[4:0]

Instruction Summary

Содержание PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов