manualshive.com logo in svg

NXP Semiconductors PXN2020, Справочное руководство, Страница: 234 / 1376

Поделиться
Скачать
NXP Semiconductors PXN2020 Скачать руководство пользователя страница 234

System Integration Unit (SIU)

PXN20 Microcontroller Reference Manual, Rev. 1

8-52

Freescale Semiconductor

8.3.2.36

Parallel GPIO Pin Data Input Register 4 (SIU_PGPDI4)

Reads to the SIU_PGPDI4 register provide the parallel GPIO pin data input for PJ0:PJ15 and PK0:PK10. 
Writes have no effect.

Reads of this register are coherent with the registers SIU_GPDI128_131, SIU_GPDI132_135, 
SIU_GPDI136_139, SIU_GPDI140_143, SIU_GPDI144_147, SIU_GPDI148_151, and 
SIU_GPDI152_154.

8.3.2.37

Masked Parallel GPIO Pin Data Output Register 1 (SIU_MPGPDO1)

The purpose of the masked parallel GPIO pin data output registers is to allow any combination of bits in 
a 16-bit parallel GPIO pin data output port to be updated in a single 32-bit write operation, while allowing 
other bits to maintain their previous state. This is accomplished by grouping each 16-bit port with a 16-bit 
mask register, and only updating those bits in the data register for which the corresponding mask bit is set. 

For example, if the current state of the port B parallel GPIO pin data output register is 0x1234 and you 
want to change only bits [12:15] (i.e., the 4) to be an 8, then a 32-bit write with a mask value of 0x000C 
and data value of 0x0008 (i.e.,0x000C_0008) would be performed.

The masked parallel GPIO pin data output registers always read as 0.

The SIU_MPGPDO1 register contains the Masked Parallel GPIO Pin Data Output for PB[0:15]. 

Offset:

SI 0x0C4C

Access: User read-only

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

PG0:PG15

W

Reset

U

U

U

U

U

U

U

U

U

U

U

U

U

U

U

U

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

PH0:PH15

W

Reset

U

U

U

U

U

U

U

U

U

U

U

U

U

U

U

U

Figure 8-43. Parallel GPIO Pin Data Input Register 3 (SIU_PGPDI3)

Offset:

SI 0x0C50

Access: User read-only

0

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

R

PJ0:PJ15

W

Reset

U

U

U

U

U

U

U

U

U

U

U

U

U

U

U

U

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

R

PK0:PK10

0

0

0

0

0

W

Reset

U

U

U

U

U

U

U

U

U

U

U

0

0

0

0

0

Figure 8-44. Parallel GPIO Pin Data Input Register 4 (SIU_PGPDI4)

Содержание PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов