manualshive.com logo in svg

NXP Semiconductors PXN2020, Справочное руководство, Страница: 882 / 1376

Поделиться
Скачать
NXP Semiconductors PXN2020 Скачать руководство пользователя страница 882

Enhanced Modular Input/Output Subsystem (eMIOS200)

PXN20 Microcontroller Reference Manual, Rev. 1

28-60

Freescale Semiconductor

28.8

Initialization/Application Information

On resetting the eMIOS200 all unified channels enter GPIO input mode.

28.8.1

Considerations

Before changing an operating mode, the unified channel must be programmed to GPIO mode and 
EMIOS_CADR[

n

] and EMIOS_CBDR[

n

] registers must be updated with the correct values for the next 

operating mode. Then the EMIOS_CCR[

n

] register can be written with the new operating mode. If a 

unified channel is changed from one mode to another without performing this procedure, the first operation 
cycle of the selected time base can be random, i.e., matches can occur in random time if the contents of 
EMIOS_CADR[

n

] or EMIOS_CBDR[

n

] were not updated with the correct value before the time base 

matches the previous contents of EMIOS_CADR[

n

] or EMIOS_CBDR[

n

].

When interrupts are enabled, the software must clear the FLAG bits before exiting the interrupt service 
routine.

28.8.2

Application Information

Correlated output signals can be generated by all output operation modes. The OU[

n

] bits in 

EMIOS_OUDR can be used to control the update of these output signals. 

In order to guarantee the internal counters of correlated channels are incremented in the same clock cycle, 
the internal prescalers must be set before enabling the global prescaler. If the internal prescalers are set 
after enabling the global prescaler, the internal counters may increment in the same ratio but at a different 
clock cycle.

It is recommended to drive output disable input signals with the emios_flag_out signals of some unified 
channels running in SAIC mode. When an output disable condition happens, the software interrupt routine 
must service the output channels before servicing the channels running SAIC. This procedure avoids 
glitches in the output pins.

28.8.3

Time Base Generation

For MC, OPWFM, and OPWM with internal clock source operation modes, the internal counter rate can 
be modified by configuring the clock prescaler ratio. 

Figure 28-57

 shows an example of a time base with 

prescaler ratio equal to one. When the prescaler is greater than one, the counter is immediately cleared on 
a match and then incremented in the next prescaled clock edge, except when running in OPWFM mode or 
MC mode with internal clock source. In these cases, the counter will skip the next prescaled clock edge 
and continue incremented on subsequent edges, as shown in 

Figure 28-58

.

NOTE

MCB, OPWFMB, and OPWMB modes have a different behavior.

Содержание PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов