manualshive.com logo in svg

NXP Semiconductors PXN2020, Справочное руководство, Страница: 888 / 1376

Поделиться
Скачать
NXP Semiconductors PXN2020 Скачать руководство пользователя страница 888

Controller Area Network (FlexCAN)

PXN20 Microcontroller Reference Manual, Rev. 1

29-4

Freescale Semiconductor

29.1.3.3

Listen-Only Mode

In this mode, transmission is disabled, all error counters are frozen, and the module operates in a CAN 
error passive mode. Only messages acknowledged by another CAN station are received. If FlexCAN 
detects a message that has not been acknowledged, it flags a BIT0 error (without changing the REC), as if 
it was trying to acknowledge the message.

29.1.3.4

Loop-Back Mode

The module enters this mode when the LPB bit in the control register is asserted. In this mode, FlexCAN 
performs an internal loop back that can be used for self test operation. The bit stream output of the 
transmitter is internally fed back to the receiver input. The Rx CAN input pin is ignored and the Tx CAN 
output goes to the recessive state (logic 1). FlexCAN behaves as it normally does when transmitting, and 
treats its own transmitted message as a message received from a remote node. In this mode, FlexCAN 
ignores the bit sent during the ACK slot in the CAN frame acknowledge field to ensure proper reception 
of its own message. Transmit and receive interrupts are generated.

29.1.3.5

Module-Disabled Mode

This low-power mode is entered when the MDIS bit in the CAN

x

_MCR register is asserted. When 

disabled, the clocks to the CAN protocol interface and message buffer management sub-modules are shut 
down. Exit from this mode is done by negating the MDIS bit in the CAN

x

_MCR register.

29.1.3.6

Halt Mode

This low power mode is entered when the corresponding HLT bit in the SIU_HLT0 is asserted. The HLT 
bit drives the stop input to the module. When in halt mode, the module puts itself in an inactive state and 
then informs the CPU that its clock can be shut down. 

Exit from this mode happens when the HLT bit is de-asserted. 

29.2

External Signal Description

Please refer to 

Table 3-1

 and 

Section 3.4, Detailed Signal Description,

 for a complete description of the 

FlexCAN signals.

29.3

Memory Map and Registers

This section provides a detailed description of all FlexCAN registers.

29.3.1

Module Memory Map

The complete memory map for an individual FlexCAN module is shown in 

Table 29-1

. Except for the base 

addresses, all FlexCAN modules have identical memory maps.

The Rx global mask (CAN

x

_RXGMASK), Rx buffer 14 mask (CAN

x

_RX14MASK) and the Rx buffer 

15 mask (CAN

x

_RX15MASK) registers are provided for backwards compatibility, and are not used when 

the BCC bit in CAN

x

_MCR is asserted.

Содержание PXN2020

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов