Norwood The Grain Handler 10 Скачать руководство пользователя страница 106

Страница: 106 / 130

5 - MAINTENANCE

5-16

2500 Hours Or Annually

Change Gearbox Oil

The gearbox oil must be changed every 2500 hours of op

eration. Use the following steps to change the gearbox oil.

WARNING

HOT LIQUID HAZARD

The gearbox oil must cool before changing the oil. Hot oil

can cause burns if it contacts exposed skin.

Failure to comply could result in serious injury.

1. Allow the gearbox to cool slightly before changing oil. For

best results, drain the oil while the reservoir is still warm

to the touch (not hot).

2. Use the instructions on the following pages to expose the

gearbox for changing the oil.

(See"Upper Gearbox" on

page 5-10)

(See"Lower Gearbox" on page 5-11)

Then

come back to this page and resume on step # 3.

3. Place a large pan or pail under the gearbox. Remove

drain plug from Upper gearbox.

(See Fig. # 5-19)

Drain Plug

Fig. # 5-19 Upper Gearbox Drain Plug

4. Place a large pan or pail under the gearbox. Remove

drain plug for Lower gearbox.

(See Fig. # 5-20)

Fig. # 5-20 Lower Gearbox Drain Plug

Drain Plug

5. Refill with an SAE food grade gear oil (FMO-90-AW) for

all operating conditions.

The gearbox capacities are listed below:

Upper Gearbox:

FMO-90-AW Oil Reservoir Capacity

Ounces

Liters

.739

Lower Gearbox:

FMO-90-AW Oil Reservoir Capacity

Ounces

Liters

10.5

.310

6. Check oil level. Top up as required.
7. After filling, close and secure the cap.

Содержание The Grain Handler 10



































































































































Результаты поиска

Содержание The Grain Handler 10

Отзывы:

Norwood The Grain Handler 10, Руководство оператора, Страница: 106 / 130

Результаты поиска

Содержание The Grain Handler 10

Отзывы: