Norwood The Grain Handler 10 Скачать руководство пользователя страница 105

Страница: 105 / 130

5 - MAINTENANCE

5-15

As Required

Replacing the Drive Belts

Before your belt(s) fail, it will usually show signs

of wear. If the ribs facing the pulley are missing in

some areas, it may function quite well, but if numer

ous ribs are missing, replace the drive belt right away.

If one side is wearing unevenly, you could have a mis

aligned belt. This could be a problem with the pulley.

Cracks and rot are, of course, indications that you should

replace the drive belt. Any crack that’s more than half

way through the belt has to be replaced immediately.

If your drive belt is damaged, don’t take chances, a damaged

belt could cause extensive damage to other components.

When in doubt, it’s best to replace.

DANGER

NEVER ENTER BIN UNLESS ALL POWER IS LOCKED

OUT AND ANOTHER PERSON IS PRESENT.

Exposed auger and moving parts can cause severe in-

jury or death. Rotating augers are dangerous! Flowing

grain may trap and suffocate.

FAILURE TO HEED THIS WARNING MAY CAUSE SERI-

OUS INJURY OR DEATH.

DANGER

ROTATING AUGER HAZARD KEEP AWAY

To prevent serious injury or death from rotating

augers:

1. Do not enter bin unless power is locked out.

2. Turn machine OFF, shut down and lock out power source,

unplug power cord and wait for all moving parts to stop before

inspecting, servicing or repairing machine.

3. Keep body, hair, and clothing away from moving parts.

4. Stay away from rotating augers. Keep others away.

FAILURE TO HEED THIS WARNING MAY CAUSE

SERIOUS INJURY OR DEATH.

1. Clear area of bystanders.
2. To replace the drive belts, follow steps 20-27

(See"20.

Install the "V-Belts"" on page 3-22)

Fig. # 5-18 Install V-Belts

Содержание The Grain Handler 10



































































































































Результаты поиска

Содержание The Grain Handler 10

Отзывы:

Norwood The Grain Handler 10, Руководство оператора, Страница: 105 / 130

Результаты поиска

Содержание The Grain Handler 10

Отзывы: