Norwood The Grain Handler 10 Скачать руководство пользователя страница 92

Страница: 92 / 130

5 - MAINTENANCE

5-2

FLUIDS AND LUBRICANTS
Hydraulic Oil:

Use an ISO grade SAE food grade gear oil (FMO-90-AW) for

all operating conditions.

Storing Lubricants:

Your machine can operate at top efficiency only if clean lu

bricants are used.

Use clean containers to handle all lubricants. Store them in an

area protected from dust, moisture and other contaminants.

Make certain that all containers are properly marked to Identify

their contents.

Grease:

Use an SAE multipurpose high temperature grease with ex

treme pressure (EP) performance. Also acceptable, SAE

multipurpose lithium based grease.

Other greases may be used if they meet the following:
• NLGI Performance Classification GC-LB
• ISO-L-X-BDHB 2 or DIN KP 2 N-10 Lithium Complex

Non-Synthetic Base Oil (100 to 220 mm2/s @ 40°C)

Greasing

Use the

Maintenance Chart

provided on page

(See "MAIN-

TENANCE CHART" On Page 5-3)

to keep a record of all

scheduled maintenance.

1. Use only a hand-held grease gun for all greasing. An

air-powered greasing system can damage the seals on

bearings and lead to early failures.

2. Wipe grease fitting with a clean cloth before greasing to

avoid injecting dirt and grit.

3. All universal joints on the machine are greaseable. They

require minimal lubricant. Recommended greasing is 1

small stroke every 2 weeks. Be careful not to over-grease,

as this may push the seal out.

4. Replace and repair broken fittings immediately.
5. If fittings will not take grease, remove and clean thorough

ly. Also clean lubricant passageway. Replace fitting if

necessary.

SERVICING INTERVALS

Make sure your Power Sweep is ready to go to the field when

you are. Perform the service and maintenance procedures

that are recommended in this section to prepare for the next

season. Careful maintenance preparation will save time and

expense as you enter the busy season.

The periods recommended on page

(See "MAINTENANCE

CHART" On Page 5-3)

are based on normal operating

conditions. Severe or unusual conditions may require more

frequent lubrication and oil changes.

Schedules may vary depending on equipment options con

tained in the present unit.

Lubrication Symbols

Lubricate at the hourly interval indicated on symbol. Use SAE

multi-purpose high-temperature grease with extreme pressure

(EP) performance. SAE multi-purpose lithium-based grease

is also acceptable.

Repack bearings at the hourly interval indicated on symbol.

Use SAE multi-purpose high-temperature grease with extreme

pressure (EP) performance. SAE multi-purpose lithium-based

grease is also acceptable.

Pack bearings by hand or with a bearing packer machine

Содержание The Grain Handler 10



































































































































Результаты поиска

Содержание The Grain Handler 10

Отзывы:

Norwood The Grain Handler 10, Руководство оператора, Страница: 92 / 130

Результаты поиска

Содержание The Grain Handler 10

Отзывы: