Norwood The Grain Handler 10 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 130

Norwood The Grain Handler 10 Скачать руководство пользователя страница 3

i

Disclaimer

This document is based on information available at the time of its publication. While efforts have been made to be accurate,

the information contained herein does not purport to cover all details or variations, nor to provide for every possible contin

-

gency in connection with installation, operation, or maintenance. Features may be described herein which are not present

in all systems. Norwood Sales Inc. assumes no obligation of notice to holders of this document with respect to changes

subsequently made.

Norwood Sales Inc. makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no

responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties

of merchantability or fitness for purpose shall apply.

Trademark Information

Read and Understand

WARNING

Read and follow all instructions and safety precautions in this
manual and all other manuals for products associated with this
machine as well as in all on-product warning decals. Failure
to do so could result in death or serious injury, or property
damage. Contact your Norwood dealer if any of your manuals
are missing or illegible or you have questions.

Preface

This Operator's Manual is intended for use with the following: The Grain Handler U-Trough Power Sweep

Models:

8” U-Trough Power Sweep

s

Sizes: 18’ 19’ 21’ 24’ 27’ 30’ 33’ 36’ 42’ 48’

10” U-Trough Power Sweeps

Sizes: 18’ 19’ 21’ 24’ 27’ 30’ 33’ 36’ 42’ 48’ 54’ 60’

Revision History

Issue

Date

Reasons

for

Change

10-5-00007

April 4th 2021

Initial Release

OSHA

®

Is a registered trademark of the Occupational Safety

& Health Administration and is so acknowledged.

ASABE

®

Is a registered trademark of the American Society of

Agricultural and Biological Engineers and is so acknowledged.

NFPA

®

Is a registered trademark of the National Fire

Protection Association and is so acknowledged.

ANSI

®

Is a registered trademark of the American National

Standards Institute and is so acknowledged.

NEMA

®

Is a registered trademark of the National Electrical

Manufacturers Association and is so acknowledged.

Any trademarks not directly mentioned are also acknowledged.

«
1
2
3
4
5
...
»

Содержание The Grain Handler 10



































































































































Отзывы:

Нет отзывов