Norwood The Grain Handler 10 Скачать руководство пользователя страница 97

Страница: 97 / 130

5 - MAINTENANCE

5-7

First 10 Hours Of Operation
And Then
50 Hours Or Weekly
Grease Universal Joints

DANGER

NEVER ENTER BIN UNLESS ALL POWER IS LOCKED

OUT AND ANOTHER PERSON IS PRESENT.

Exposed auger and moving parts can cause severe in-

jury or death. Rotating augers are dangerous! Flowing

grain may trap and suffocate.

FAILURE TO HEED THIS WARNING MAY CAUSE SERI-

OUS INJURY OR DEATH.

DANGER

ROTATING AUGER HAZARD KEEP AWAY

To prevent serious injury or death from rotating

augers:

1. Do not enter bin unless power is locked out.

2. Turn machine OFF, shut down and lock out power

source, unplug power cord and wait for all moving parts

to stop before inspecting, servicing or repairing machine.

3. Keep body, hair, and clothing away from moving parts.

4. Stay away from rotating augers. Keep others away.

FAILURE TO HEED THIS WARNING MAY CAUSE

SERIOUS INJURY OR DEATH.

Your equipment can operate at top efficiency, but only if it is

properly maintained at a regular interval.

Use an SAE multipurpose high temperature grease with ex

treme pressure (EP) performance. Also acceptable, SAE

multipurpose lithium based grease.

Pump until the grease becomes visible.
1. Grease 1 point as indicated by the following symbol

for the universal joint located on Power Sweep

gearbox the first 10 hours and then every Week or (50

hours) of use.

(See Fig. # 5-3)

Fig. # 5-3 Grease U-Joint

10/50

2. Grease 1 point as indicated by the following symbol

for the universal joint located on Inclined Pow

erhead the first 10 hours and then every Week or (50

hours) of use.

Fig. # 5-4 Grease U-Joint

10/50

DANGER

MISSING GUARD HAZARD

Machine is shown with guard removed for illustrative purposes.

• Turn machine OFF, shut down and lock out power source, unplug power cord

and wait for all moving parts to stop before inspecting, servicing or repairing

machine.

• Keep body, hair, and clothing away from moving auger flighting and moving parts.
• Do not operate with any guards removed or modified. Keep guards in good

working order. Failure to comply could result in death or serious injury.

Содержание The Grain Handler 10



































































































































Результаты поиска

Содержание The Grain Handler 10

Отзывы:

Norwood The Grain Handler 10, Руководство оператора, Страница: 97 / 130

Результаты поиска

Содержание The Grain Handler 10

Отзывы: