manualshive.com logo in svg

Norwood The Grain Handler 10, Руководство оператора, Страница: 98 / 130

Поделиться
Скачать
Norwood The Grain Handler 10 Скачать руководство пользователя страница 98

5 - MAINTENANCE

5-8

Every 10 Hours Of Operation

Grease Buzz Wheel

    

DANGER

NEVER ENTER BIN UNLESS ALL POWER IS LOCKED 

OUT AND ANOTHER PERSON IS PRESENT.

Exposed auger and moving parts can cause severe in-

jury or death. Rotating augers are dangerous!  Flowing 

grain may trap and suffocate.

FAILURE TO HEED THIS WARNING MAY CAUSE SERI-

OUS INJURY OR DEATH.

    

DANGER

ROTATING AUGER HAZARD KEEP AWAY 

To prevent serious injury or death from rotating 

augers: 

1.   Do not enter bin unless power is locked out. 

2.   Turn  machine  OFF,  shut  down  and  lock  out  power 

source, unplug power cord and wait for all moving parts 

to stop before inspecting, servicing or repairing machine.

3.   Keep body, hair, and clothing away from moving parts.

4.   Stay away from rotating augers. Keep others away.

FAILURE TO HEED THIS WARNING MAY CAUSE 

SERIOUS INJURY OR DEATH.

Your equipment can operate at top efficiency, but only if it is 

properly maintained at a regular interval. 

Use an SAE multipurpose high temperature grease with  ex

-

treme  pressure  (EP)  performance.  Also acceptable, SAE 

multipurpose lithium based grease. 

Pump until the grease becomes visible.

1.   Grease  1  point  as  indicated  by  the  following  symbol 

40

 for the grease zerk located on the Buzz Wheel.

every 10 hours of use.  

(See Fig. # 5-5)

Fig. # 5-5 Grease Buzz Wheel

Loosen Nut

To Open 

Inspection

Cover

10

2.   Inspect gears for proper amount of grease. 

(See Fig. # 

5-6)

Inspect Gears 

For Proper 

Amount Of

Grease

Fig. # 5-6 Inspect Buzz Wheel Gears

3.  Grease  1  point  as  indicated  by  the  following  symbol 

40

 for the grease zerk located on the Buzz Wheel.

every 10 hours of use.

Содержание The Grain Handler 10



































































































































Отзывы:

Нет отзывов