Norwood The Grain Handler 10 Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 130

Norwood The Grain Handler 10 Скачать руководство пользователя страница 87

4 - WORKING OPERATIONS

4-9

Unload Grain From the Center Sump

1. Disengage the Power Sweep gearbox (Push Power

Sweep Engagement Lever towards discharge outlet to

disengage Power Sweep).

Fig. # 4-15 Power Sweep Engagement Lever

DISENGAGE

ENGAGE

POWER SWEEP

ENGAGEMENT

LEVER

POWER SWEEP

LOCKING

LEVER

1. STOP the motor.
2. Lift up the "Power Sweep Locking Lever".
3. To engage the "Power Sweep" push the
"Power Sweep Engagement Lever" in
towards the bin.
4. Turn the pulley by hand (The motor must
be stopped) and listen for the gearbox to
"CLICK" into gear.
5. To Disengage the "Power Sweep" pull the
"Power Sweep Engagement Lever" out
towards the discharge spout.
6. Engage "Power Sweep Locking Lever".

POWER

2. Close all Discharge Slide Gates (center, and intermediate

sumps).

(See Fig. # 4-16)(See Fig. # 4-17)

Fig. # 4-16 Center Gate Control

OPEN

CLOSE

Center Gate

Control

OPEN

CLOSE

Intermediate

Gate(s) Control

Fig. # 4-17 Intermediate Gate(s) Control

3. Start the electric motor.
4. The Rack & Pinion gate controls are set so the Center

Hopper Sump gate must be opened first. Read the in

-

struction decal under the controls and open the gates in

the sequence specified. Failure to follow this sequence

could result in severe damage to the grain bin structure.

When starting to unload, open the center sump slightly.

Ensure that grain flows out of the discharge end at a

(See Fig. # 4-19)

ALWAYS LOAD AND UNLOAD FROM THE CENTER OF THE GRAIN BIN

• The center hopper gate must be opened first to empty the grain bin.
• Only when grain stops flowing from the center hopper can the intermediate hopper gates
can be opened.

Failure to comply could result in structural damage, serious injury,

or death.

Fig. # 4-18 Warning Decal

Fig. # 4-19 Instructional Decal

OPERATING INSTRUCTIONS

STEP 1 - Open center hopper gate first, unload until grain flow stops. Only when NO grain remains

above the center hopper can the intermediate hopper gate(s) be opened.

STEP 2 - Open the intermediate hopper gate(s) until grain flow stops.

STEP 3 - Stop the motor, engage the bin sweep gearbox lever to remove the remaining grain.

STEP 4 - Close all hopper gates and empty the remaining grain from the u-trough.

STEP 5 - Stop the motor, disengage bin sweep gearbox lever, return bin sweep over the hoppers.

STEP 6 - The grain bin is now ready to be refilled.

5. Continue to open the center sump and watch for constant

product flow at the discharge outlet. Do this until center

sump is fully open.

6. For the first 30 minutes, check that the underfloor auger

flighting functions without excessive vibration. Once the

grain mass has been fully drawn down, you are now ready

to proceed with unloading grain from the intermediate

sumps.

«
...
85
86
87
88
89
...
»

Содержание The Grain Handler 10



































































































































Отзывы:

Нет отзывов