Norwood The Grain Handler 10 Скачать руководство пользователя страница 25

Страница: 25 / 130

2 - SAFETY INFORMATION

2-13

Safety Decals

The following safety decals are placed on your machine as a guide for your safety and for those working with you. Walk around

the machine and note the content and location of these safety decals before operating your machine.

Keep safety decals clean and legible. Clean safety decals with a soft cloth, water, and a gentle detergent. Do not use solvent,

gasoline, or other harsh chemicals. Solvents, gasoline, and other harsh chemicals may damage or remove safety decals.

Replace all safety decals that are damaged, missing, painted over, or illegible. If a safety decal is on a part that is replaced,

make sure the safety decal is installed on the new part. See your dealer for replacement safety decals.

Safety decals that display the “Read Operator’s Manual” symbol are intended to direct the operator to the operator’s manual

for further information regarding maintenance, adjustments, or procedures for particular areas of the machine.

When a safety decal displays this symbol, refer to the appropriate page of the operators manual.

Safety Decal Locations

Item

Part

Number

Description

Qty. Item

Part

Number

Description

Qty.

90-44-0582 Decal, Warning Safety Information Power Sweep

90-44-0359 Decal, Rotating Auger Hazard Keep Away

90-44-0011 * Decal, Danger Never Enter Bin (Large)

90-44-0221 Decal, Buzz Saw Shear Bolt (Option)

90-44-0012 Decal, Danger Never Enter Bin (Small)

90-44-0579 Decal, Warning Bin Unloading Instructions

90-44-0578 Decal, Rotating Parts Hazard-Auger

90-44-0580 Decal, Operating Instructions - Bin Unloading

90-44-0021 Decal, Danger Missing Guard (2 x 3.5)

90-44-0581 Decal, Operating Instructions - Power Sweep

90-44-0167 Decal, Rotating Parts Hazard

90-44-0583

Decal, Operating Instructions-Power Sweep Engage-Dis

* Not shown In this view

N ING

DANGER

MISSING GUARD HAZARD

Machine is shown with guard removed

for illustrative purposes.

• Turn machine OFF, shut down and lock

out power source, unplug power cord

and wait for all moving parts to stop

before inspecting, servicing or repairing

machine.

• Keep body, hair, and clothing away from

moving auger flighting and moving parts.

• Do not operate with any guards removed

or modified. Keep guards in good work

ing order. Failure to comply could result

in death or serious injury.

Fig. # 2-7 Safety Decal Locations (Horizontal Powerhead & Standard Drive Wheel Option)

Содержание The Grain Handler 10



































































































































Результаты поиска

Содержание The Grain Handler 10

Отзывы:

Norwood The Grain Handler 10, Руководство оператора, Страница: 25 / 130

Результаты поиска

Содержание The Grain Handler 10

Отзывы: