Norwood The Grain Handler 10 Скачать руководство пользователя страница 111

Страница: 111 / 130

6 - TROUBLESHOOTING

6-3

Underfloor flighting is

noisy.

Flighting connection to powerhead shaft is

loose.

Remove flange connector bolts and pull out the

flighting and ensure all hardware is tightened.

Center gearbox spline connection is not

straight.

Ensure gearbox is set straight into the U-trough.

Flighting is bent.

Remove U-Trough flighting. Check for

straightness by rolling across flat concrete area.

Straighten or replace as necessary.

Power Sweep engaged

and running, but not

advancing

Backboard catching on bin floor.

Ensure backboard clearance is at 1/4” from grain

bin floor.

Rubber on wheel wore down.

Replace with new rubber drive wheel.

Grain condition wet, hard-packed, moldy

Sweep will perform poorly if grain is out of

condition

End wheel contacting bin wall or protruding

grain bin bolts.

Adjust sweep away from bin wall, and or cut or

grind protruding bolts.

U-Trough auger is unable

to move the grain that the

sweep is dumping into

the center hopper.

Obstruction in center hopper.

Remove obstruction.

Intermediate hopper(s) are open, flooding the

U-Trough auger.

Close intermediate hoppers.

Flighting is not timed correctly on the U-Trough

auger.

Pull out underfloor flighting, ensure that flighting is

not damaged. (Flighting must make a continuous

spiral).

Troubleshooting Field Problems (Cont.)

Содержание The Grain Handler 10



































































































































Результаты поиска

Содержание The Grain Handler 10

Отзывы:

Norwood The Grain Handler 10, Руководство оператора, Страница: 111 / 130

Результаты поиска

Содержание The Grain Handler 10

Отзывы: