Norwood The Grain Handler 10 Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 130

Norwood The Grain Handler 10 Скачать руководство пользователя страница 84

4 - WORKING OPERATIONS

4-6

Power Sweep Engagement Lever

The lever to engage or disengage the gearbox that drives

the Power Sweep is located on the u-trough tube outside the

grain bin.

(See Fig. # 4-7)

POWER SWEEP

LOCKING

LEVER

POWER SWEEP

ENGAGEMENT

LEVER

Fig. # 4-7 Power Sweep Engagement Lever Location

Refer to figures

(See Fig. # 4-7)

&

(See Fig. # 4-8)

while

following the instructions below.
1.   STOP the motor.
2.   Lift up the "Power Sweep Locking Lever".
3.   To engage the "Power Sweep" push the "Power Sweep

Engagement Lever" in towards the bin.

4. Turn the pulley by hand (The motor mu

st be stopped) and listen for the gearbox to "CLICK"

into gear.

5. To Disengage the "Power Sweep" pull the "Power Sweep

Engagement Lever" out towards the discharge spout.

6. Engage "Power Sweep Locking Lever".

DISENGAGE

ENGAGE

POWER SWEEP

ENGAGEMENT

LEVER

POWER SWEEP

LOCKING

LEVER

1. STOP the motor.
2. Lift up the "Power Sweep Locking Lever".
3. To engage the "Power Sweep" push the
"Power Sweep Engagement Lever" in
towards the bin.
4. Turn the pulley by hand (The motor must
be stopped) and listen for the gearbox to
"CLICK" into gear.
5. To Disengage the "Power Sweep" pull the
"Power Sweep Engagement Lever" out
towards the discharge spout.
6. Engage "Power Sweep Locking Lever".

POWER

Fig. # 4-8 Power Sweep Engagement Lever Instructional

Decal

Motor Mount Belt Tension Lever

The

"Motor Mount Belt Tension Lever"

raises or lowers

the

"Motor Mount Base"

which increases or decreases the

drive belt tension. The

"Motor Mount Belt Tension Lever"

is located on the right side of either the horizontal or inclined

powerhead.

(See Fig. # 4-9)

INCREASE

BELT

TENSION

DECREASE

BELT

TENSION

MOTOR

MOUNT

BASE

MOTOR MOUNT

BELT TENSION

LEVER

Fig. # 4-9 Motor Mount Belt Tension Lever

1. To increase the drive belt tension, adjust the Motor Mount

Belt Tension Lever upwards.

(See Fig. # 4-9)

2. To decrease the drive belt tension, adjust the Motor Mount

Belt Tension Lever downwards.

(See Fig. # 4-9)

DRIVE

BELTS

Fig. # 4-10 Drive Belts

«
...
82
83
84
85
86
...
»

Содержание The Grain Handler 10



































































































































Отзывы:

Нет отзывов