manualshive.com logo in svg

Norwood The Grain Handler 10, Руководство оператора, Страница: 13 / 130

Поделиться
Скачать
Norwood The Grain Handler 10 Скачать руководство пользователя страница 13

2 - SAFETY INFORMATION

2-1

2.0 - SAFETY INFORMATION

Safety Rules And Signal Word Definitions

Personal Safety:

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Read and understand all the safety 

messages in this manual and associated equipment manuals before you operate or service the machine. Obey all safety 

messages that follow this symbol to avoid possible death or serious injury.

Throughout this manual and on machine decals, you will find the signal words 

DANGER

, 

WARNING

, and 

CAUTION 

followed by special instructions.  These precautions are intended for the personal safety of you 

and those working with you.

DANGER

  

DANGER;

 Indicates a hazardous situation which, if not avoided, will result in death or serious 

injury.  The color associated with 

DANGER

 on the machine decals is 

RED

.

      

WARNING

  

WARNING;

 Indicates a hazardous situation which, if not avoided, could result in death or serious 

injury.  The color associated with WARNING on the machine decals is 

ORANGE

.

CAUTION

  

CAUTION;

 Used with the safety alert symbol, indicates a hazardous situation which, if not avoided, 

could result in minor or moderate injury.  

CAUTION

 may also be used to alert against unsafe practices associated with events

which could lead to personal injury. The color associated with 

CAUTION

 on the machine decals is 

YELLOW

.

FAILURE TO FOLLOW DANGER, WARNING, AND CAUTION MESSAGES COULD RESULT IN 

DEATH OR SERIOUS INJURY.

Machine Safety & Informational:

NOTICE

  

Notice

 or 

Note

 indicates a situation which, if not avoided, could result in machine or property 

damage. The color associated with 

Notice

 on the machine decals is 

BLUE

.

Throughout this manual you will find the signal word 

Notice

 followed by special instructions to prevent machine or property 

damage. The word 

Notice

 is used to address practices not related to personal safety. 

IMPORTANT

 

Important

 indicates a situation which, if not avoided, could result in machine or property 

damage. The color associated with 

Important

 on the machine decals is white text on a 

WHITE 

background.

Throughout this manual you will find the word 

Important

 followed by additional information about a step, procedure, or other 

information in the manual. The word 

Important

 is used to address practices not related to personal safety.

Operating Instructions

 indicates proper steps to complete a task, which, if not avoided, could result in machine or property 

damage. The color associated with 

Operating Instructions

 on the machine decals is white text on a 

BLACK 

background.

Throughout this manual you will find the phrase 

Operating Instructions

 followed by additional information about a step, 

procedure, or other information in the manual. The phrase 

Operating Instructions

 is used to address practices not related 

to personal safety.

Содержание The Grain Handler 10



































































































































Отзывы:

Нет отзывов