Norwood The Grain Handler 10 Скачать руководство пользователя страница 66

Страница: 66 / 130

3 - INSTALLATION

3-26

Standard Or Buzz Drive Wheel Installation

The following instructions are for installing the “Standard

Drive Wheel” accessory for all models of the Power Sweep

To install the “Standard Drive Wheel”, proceed as follows:

NOTE

If you are switching from the

Buzz Wheel Drive Wheel

Option

to the

Standard Drive Wheel Option

or the other

way around, the dis-assembly is the same with the excep

tion of the weight difference. Installation for the first time is

also the same.

(See Fig. # 3-69) (See Fig. # 3-70)

MODELS:

8” U Trough Powersweeps

802-19-1102U, 802-21-1102U, 802-24-1102U, 802-27-1102U,

802-30-1102U, 802-33-1102U, 802-36-1102U, 802-42-1102U,

802-48-1102U

10” U Trough Powersweeps

102-19-1102U, 102-21-1102U, 102-24-1102U, 102-27-1102U,

102-30-1102U, 102-33-1102U, 102-36-1103U, 102-42-1104U,

102-48-1104U, 102-54-1104U, 102-60-1105U

Estimated Completion Time:

30 Min’s.

Parts:

(See Page # 3-38)

REQUIRED TOOLS / SUPPLIES:

(1) Hand Truck

(1) Sawhorse

(1) 9/16” Socket

(1) 9/16” Open End Wrench

(1) 3/8” Ratchet

(1) 3/8” Pneumatic or Battery

Powered Impact Wrench

(1) Torque Wrench

(1) Lifting Device

(1) Lifting Strap (100 lb or

greater)

DANGER

NEVER ENTER BIN UNLESS ALL POWER IS LOCKED

OUT AND ANOTHER PERSON IS PRESENT.

Exposed auger and moving parts can cause severe in-

jury or death. Rotating augers are dangerous! Flowing

grain may trap and suffocate.

FAILURE TO HEED THIS WARNING MAY CAUSE SERI-

OUS INJURY OR DEATH.

DANGER

ROTATING AUGER HAZARD KEEP AWAY

To prevent serious injury or death from rotating

augers:

1. Do not enter bin unless power is locked out.

2. Turn machine OFF, shut down and lock out power

source, unplug power cord and wait for all moving parts

to stop before inspecting, servicing or repairing machine.

3. Keep body, hair, and clothing away from moving parts.

4. Stay away from rotating augers. Keep others away.

FAILURE TO HEED THIS WARNING MAY CAUSE

SERIOUS INJURY OR DEATH.

SERVICE PROCEDURE:

Preparation:

1. The "Standard Drive Wheel" comes fully assembled and

ready for assembly to the Power Sweep.

Fig. # 3-65 Standard Drive Wheel

2. If assembly needs to take place inside the grain bin, then

follow the safety section

(See"2.0 - SAFETY INFORMA-

TION" on page 2-1)

in the manual before installation.

Содержание The Grain Handler 10



































































































































Результаты поиска

Содержание The Grain Handler 10

Отзывы:

Norwood The Grain Handler 10, Руководство оператора, Страница: 66 / 130

Результаты поиска

Содержание The Grain Handler 10

Отзывы: