Norwood The Grain Handler 10 Скачать руководство пользователя страница 100

Страница: 100 / 130

5 - MAINTENANCE

5-10

100 Hours Or Monthly

Check The Gearbox Oil Levels

DANGER

NEVER ENTER BIN UNLESS ALL POWER IS LOCKED

OUT AND ANOTHER PERSON IS PRESENT.

Exposed auger and moving parts can cause severe in-

jury or death. Rotating augers are dangerous! Flowing

grain may trap and suffocate.

FAILURE TO HEED THIS WARNING MAY CAUSE SERI-

OUS INJURY OR DEATH.

DANGER

ROTATING AUGER HAZARD KEEP AWAY

To prevent serious injury or death from rotating

augers:

1. Do not enter bin unless power is locked out.

2. Turn machine OFF, shut down and lock out power

source, unplug power cord and wait for all moving parts

to stop before inspecting, servicing or repairing machine.

3. Keep body, hair, and clothing away from moving parts.

4. Stay away from rotating augers. Keep others away.

FAILURE TO HEED THIS WARNING MAY CAUSE

SERIOUS INJURY OR DEATH.

The Grain Handler U-Trough Power Sweep uses (Qty. 2)

gearboxes, (Qty. 1) is located on the Power Sweep head, and

the other is at the center of the grain bin next to the center

hoper sump. It is necessary to check the gearbox oil every

100 Hours Or Monthly.

FMO-90-AW Oil Reservoir Capacity

Ounces

Liters

.739

Upper Gearbox

1. Ensure the grain bin is completely empty of all product.
2. Check the level when the oil is cold by removing the cap

from the reservoir.

(See Fig. # 5-9)

3. Use an a SAE food grade gear oil (FMO-90-AW) for all

operating conditions.

4. Fill the reservoir so that oil reaches the bottom of the

threads.

(See Fig. # 5-9)

5. Rotate the auger flighting to remove any air inside the

gearbox.

6. Recheck oil level and add as necessary.
7. After filling, close and secure the cap.

Check Gearbox

Oil Level (Either

Side)

Fig. # 5-9 Check Gearbox Oil Level

Содержание The Grain Handler 10



































































































































Результаты поиска

Содержание The Grain Handler 10

Отзывы:

Norwood The Grain Handler 10, Руководство оператора, Страница: 100 / 130

Результаты поиска

Содержание The Grain Handler 10

Отзывы: