manualshive.com logo in svg

Nortel Passport 8600 Series, Пусконаладка

Поделиться
Скачать
Nortel Passport 8600 Series Скачать руководство пользователя страница 92

92

Initial steps using the NNCLI

Procedure steps

Step

Action

1

View the current setting for the primary SF/CPU by using the
following command:

show boot config master

2

Specify the slot of the primary SF/CPU by using the following
command:

boot config master <cpu-slot>

3

Save the configuration to the boot.cfg and pcmboot.cfg files.

4

Reboot the switch.

--End--

Variable definitions

Use the data in the following table to use the

boot config master

command.

Variable

Value

<cpu-slot>

Specifies the slot number for the
primary SF/CPU. This variable can be
5 or 6. The default primary is slot 5.

Changing passwords

Configure new passwords for each access level, or change the logon or
password for the different access levels of the switch. After you receive
the Nortel Ethernet Routing Switch 8600, use default passwords to initially
access the NNCLI. If you use Simple Network Management Protocol
version 3 (SNMPv3), you can change encrypted passwords.

Prerequisites

•

You must use an account with read/write/all privileges to change
passwords. For security, the switch saves passwords to a hidden file.

•

You must log on to the Global Configuration mode in the NNCLI.

Procedure steps

Step

Action

1

Change a password by using the following command:

cli password <word> <access-level>

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Copyright © 2008 Nortel Networks

.

Содержание Passport 8600 Series









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды