manualshive.com logo in svg

Nortel Passport 8600 Series, Пусконаладка

Поделиться
Скачать
Nortel Passport 8600 Series Скачать руководство пользователя страница 76

76

Initial steps using the NNCLI

Variable

Value

mode <ascii|slip|ppp>

Configures the communication mode for the
serial port. The default is American Standard
Code for Information Interchange (ASCII).

If you are configuring the modem port, you can
configure the port to use either the SLIP or the
PPP communication mode.

To configure this option to the default value, use
the

default

operator with the command.

mtu <bytes>

Configures the size of the maximum transmission
unit for a PPP link (0–2048). The default is 0. To
configure this option to the default value, use the

default

operator with the command.

my-ip <ipaddr>

Configures the IP address for the server side,
the Nortel Ethernet Routing Switch 8600, of
the point-to-point link. The default is 0.0.0.0.
Nortel recommends that you use the current IP
address for the management port. To configure
this option to the default value, use the

default

operator with the command.

peer-ip <ipaddr>

Configures the peer (PC) IP address on the
point-to-point link. The default is 0.0.0.0. The
switch assigns this value to any PC that connects
through the modem port with configured TCP/IP
properties to obtain an IP address automatically.
If the client uses a static IP address, the Nortel
Ethernet Routing Switch 8600 accepts this
address. If you use Password Authentication
Protocol (PAP) authentication, you must ensure
that the client uses the correct IP address. To
configure this option to the default value, use the

default

operator with the command.

pppfile <file>

Specifies the PPP configuration file to provide
details for authentication and other options to
include during the boot procedure of the switch.
The PPP filename is a string value of no more
than 64 characters. Identify the file in the format
{a.b.c.d:|peer:|/pcmcia/|/flash/}<file>. For more
information about this file, see

“Procedure job

aid: PPP file” (page 77)

.

ATTENTION

Do not specify a PPP filename with more than
64 characters.

To configure this option to the default value, use
the

default

operator with the command.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Copyright © 2008 Nortel Networks

.

Содержание Passport 8600 Series









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды