Nortel Passport 8600 Series Скачать руководство пользователя страница 88

Страница: 88 / 136

Initial steps using the NNCLI

Variable

Value

authentication-trap

Enables or disables generation of
authentication traps.

bootstrap

Sets SNMP initial user entry.

community

Sets community table.

contact <word>

Identifies the contact person who manages
the node. To include blank spaces in the
contact, use quotation marks (") around
the text. Use the

operator to remove

this configuration. To configure this option
to the default value, use the

default

operator with the command. The default is
[email protected].

force-iphdr-sender

Sets same SNMP and IP sender flag.

force-trap-sender

Sets SNMP trap sender IP.

group

Sets SNMP v3 group access table.

host

Specifies hosts to receive SNMP
notifications.

location <word>

Identifies the physical location of the
node. To include blank spaces in the
location, use quotation marks (") around
the text. Use the

operator to remove

this configuration. To configure this option
to the default value, use the

default

operator with the command. The default is
a Nortel address.

log

Specifies the SNMP log feature.

name <word>

Configures the system or root level
prompt name for the switch.

word

is an

ASCII string from 1 to 255 characters (for
example, LabSC7 or Closet4).

notify-filter

Creates new entry for notify filter table.

sender-ip

Sets SNMP trap sender IP.

user

Creates or modifies SNMPv3 user.

view

Creates or modifies an SNMP access
view.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Содержание Passport 8600 Series

































































































































Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды

Nortel Passport 8600 Series, Пусконаладка

Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды