manualshive.com logo in svg

Nortel Passport 8600 Series, Пусконаладка

Поделиться
Скачать
Nortel Passport 8600 Series Скачать руководство пользователя страница 35

Editing system information

35

The Chassis dialog box appears with the System tab displayed.

2

Type the contact information.

3

Type the system name.

4

Type the location information.

5

Click Apply.

6

Click Close.

--End--

Variable definitions

Use the data in the following table to configure the System tab.

Variable

Value

sysDescr

Shows the system assigned name and the
software version

sysUpTime

Shows the time since the system last
started

sysContact

Configures the contact information (in this
case, an e-mail address) for the Nortel
support group

sysName

Configures the name of this device

sysLocation

Configures the physical location of this
device

VirtualIpAddr

Configures the virtual IP address that is
advertised by the primary SF/CPU and
stored in the switch configuration file and
not the boot configuration file

VirtualNetMask

Configures the net mask of the virtual
management IP address

VirtualIpv6Address

Configures the virtual IPv6 address that
is advertised by the primary SF/CPU. and
stored in the switch configuration file and
not the boot configuration file

VirtualIPv6Prefix Length

Configures the length of the virtual IPv6
prefix entry

DnsDomainName

Configures the default domain for querying
the DNS server

LastChange

Displays the time since the last
configuration change

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Copyright © 2008 Nortel Networks

.

Содержание Passport 8600 Series









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды