manualshive.com logo in svg

Nortel Passport 8600 Series, Пусконаладка

Поделиться
Скачать
Nortel Passport 8600 Series Скачать руководство пользователя страница 57

Configuring the switch with the setup utility

57

Table 9
Job aid: Setup utility prompt descriptions (cont’d.)

Prompt

Description and action

Do you want to enable CPU
High Availability mode [n]
(y/n)?

Description: Specifies if you want to enable
CPU high availability (HA) mode. Use CPU
HA mode to recover switches with two CPUs
quickly from a failure of one of the CPUs. In
HA mode (hot standby), you synchronize and
configure the two CPUs in the same mode, so
they are compatible.

Action: Specify

y

to enable CPU high

availability (HA) mode. Accept the default (

n

),

to not enable CPU HA mode.

Do you want to enable
vlan-optimization-mode support
[n] (y/n) ?

Description: Specifies if you want to enable
support for the VLAN optimization mode.

Action: Specify y to enable VLAN
optimization mode support. Accept the
default (

n

) to not enable VLAN optimization

mode support.

Do you want to enable r-mode
support [n] (y/n) ?

Description: Specifies if you want to enable
support for the R mode support.

Action: Specify y to enable R mode support.
Accept the default (

n

) to not enable R mode

support.

Do you want to enable FTP [n]
(y/n)?

Description: Specifies if you want users to
access the switch by File transfer Protocol
(FTP).

Action: Enter

y

to enable FTP for remote

users. Accept the default (

n

) to not enable

FTP.

Do you want to enable
RLOGIN [n] (y/n)?

Description: Specifies if you want to access
the switch by Rlogin.

Action: Enter

y

to enable Rlogin for remote

users. Accept the default (

n

) to not enable

Rlogin.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Copyright © 2008 Nortel Networks

.

Содержание Passport 8600 Series









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды