Nortel Passport 8600 Series Скачать руководство пользователя страница 100

Страница: 100 / 136

100

Remote connection configuration using Device Manager

Select the properties you want to change and configure their
values.

Click OK.

--End--

Variable definitions

Use the data in the following table to configure the Properties dialog box.

Variable

Value

Status Interval

Interval you use to gather statistics
and status information (default is 20
seconds).

(IfTraps, Status Interval)

The interval, in seconds, you use
to gather statistics and status
information. Configure this value if you
select the Register for Traps box.

Hotswap Detect every

The number of intervals at which
Device Manager checks for module
hot swaps.

Enable

If you select this variable, Device
Manager polls the switch according
to the settings you select prior to the
Enable box.

Retry Count

If Device Manager cannot transmit
polling information at start up, the
number of times Device Manager
retransmits polling information.

Timeout

Length of the retry for each polling
waiting period. If you access the
device through a slow link, you can
increase the timeout interval and
change the retransmission strategy to
superlinear.

Trace

If you select this variable, you can
perform trace routes.

If you select this variable, Device
Manager registers a trap.

Listen for Traps

If you select this variable, Device
Manager monitors for a trap.

Max Traps in Log

The specified number of traps that
can exist in the trap log. The default is
500.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Содержание Passport 8600 Series

































































































































Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды

Nortel Passport 8600 Series, Пусконаладка

Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды