Nortel Passport 8600 Series Скачать руководство пользователя страница 81

Страница: 81 / 136

Configuring the switch with the setup utility

Table 11
Job aid: PPP file options (cont’d.)

Option

Description

silent_mode

Configures silent mode. PPP does
not transmit LCP packets to initiate a
connection until it receives a valid LCP
packet from the peer.

vj_max_slots <value>

Configures the maximum number of
VJ compression header slots to the
value you specify.

Table 12 "Sample PPP file" (page 81)

shows example contents from a PPP

file.

Table 12
Sample PPP file

passive_mode

lcp_echo_interval 30

lcp_echo_failure 10

require_chap

require_pap

no_vj

ipcp_accept_remote

login

chap_file "my_chap"

pap_file "my_pap"

Configuring the switch with the setup utility

Configure the switch with the setup utility to monitor system requirements
and obtain the maximum system performance.

Prerequisites

•

You must log on to the Privileged EXEC mode in the NNCLI.

Procedure steps

Step

Action

Start the setup utility by using the following command:

install

Respond to the series of questions displayed on the screen.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Содержание Passport 8600 Series

































































































































Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды

Nortel Passport 8600 Series, Пусконаладка

Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды