Nortel Passport 8600 Series Скачать руководство пользователя страница 61

Страница: 61 / 136

Configuring system identification

Variable

Value

location <location>

Changes the system location.

max-vlan-resource-reservation

<enable|disable>

Enables MAX-VLAN feature.

mgmt-virtual-ip <ipaddr/mask>

Configures mgmt virtual
IP.

ipaddr/mask

is the IP address

and network mask {a.b.c.d/x |
a.b.c.d/x.x.x.x | default}.

mgmt-virtual-ipv6 <ipv6addr/pr

efix-len>

Configures mgmt virtual
IPV6.

ipv6addr/prefix-len

is the IPV6 address. The string
length ranges from 0 to 46.

mroute-stream-limit

<enable|disable>

Global mroute stream limit
configuration.

enable|disable

enables or disables mroute stream
limit.

mtu <bytes>

Sets MTU (with CRC) to one of three
values: 1522, 1950 and 9600 bytes.
is the MTU value in the range of
1522 to 9600.

multicast-resource-reservatio

n <value>

Reserves MGIDs for IPMC
use.

value

is the number of MGIDs

reserved for IPMC use in the range
from 64 to 4083.

name <prompt>

Changes the system name.

prompt

is the box or root level prompt . The
string length ranges from 0 to 255.

portlock <on|off>

Turns portlock on/off.

sendAuthenticationTrap

<true|false>

Sets authentication trap to true or
false.

smlt-on-single-cp <enable|disa

ble> [timer <value> ]

Enables SMLT on Single CP feature.

•

enable|disable

Enables

or disable SMLT on single CP
feature.

•

[timer <value> ]

is the timer

value for SMLT on single CP
feature timer in the range of 1 to
3.

topology <on|off>

Turns topology on/off.

udp-checksum <enable|disable>

Enables or disables UDP Checksum
calculation.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Содержание Passport 8600 Series

































































































































Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды

Nortel Passport 8600 Series, Пусконаладка

Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды