manualshive.com logo in svg

Nortel Passport 8600 Series, Пусконаладка

Поделиться
Скачать
Nortel Passport 8600 Series Скачать руководство пользователя страница 106

106

Remote connection configuration using the CLI

Table 14
Job aid: Roadmap of remote connection CLI commands (cont’d.)

Command

Parameter

enable

config web-server

password <ro> <username> <password>

ftpd <true|false>

rlogind <true|false>

sshd <true|false>

telnetd <true|false>

flags

tftpd <true|false>

Assigning an IP address to the management port

Assign an IP address to the management port to use it for out-of-band
(OOB) management. The standby IP must be in the same subnet as the
master IP. Create a virtual management port in addition to the physical
management ports on the switch management modules.

ATTENTION

The virtual IP address feature is not supported in a switch with mixed Nortel
Ethernet Routing Switch 8600 8190SM modules and 8691SF/CPU modules.

Procedure steps

Step

Action

1

Assign an IP address to the management port by using the
following command:

config bootconfig net mgmt ip <ipaddr/mask> [cpu-slot

<value>]

2

Assign an IP address to a virtual management port by using the
following command:

config sys set mgmt-virtual-ip <ipaddr/mask>

3

Save the changes to the boot.cfg and config.cfg files.

--End--

Variable definitions

Use the data in the following table to use the

config bootconfig net

mgmt ip

and

config sys set mgmt-virtual-ip

commands.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Copyright © 2008 Nortel Networks

.

Содержание Passport 8600 Series









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды