manualshive.com logo in svg

Nortel Passport 8600 Series, Пусконаладка

Поделиться
Скачать
Nortel Passport 8600 Series Скачать руководство пользователя страница 11

11

.

New in this release

The following sections detail what’s new in Nortel Routing Switch 8600
Commissioning, NN46205-319 for Release 5.0:

•

“Features” (page 11)

•

“Other changes” (page 11)

Features

See the following sections for information about feature changes.

•

“NNCLI” (page 11)

NNCLI

In Release 5.0, you can use the new Nortel Command Line Interface
(NNCLI) to configure the switch. For more information about the NNCLI,
see the following sections:

•

“Initial steps using the NNCLI” (page 69)

•

“Remote connection configuration using the NNCLI” (page 113)

•

“Common procedures using the NNCLI” (page 131)

Other changes

See the following sections for information about changes that are not
feature-related.

•

“Document changes” (page 11)

Document changes

Much of the content in this document is previously released as Getting
Started, 313189-F. All document titles in the Nortel Ethernet Routing
Switch 8600 suite are changed. For more information, see Nortel Ethernet
Routing Switch 8600 Documentation Roadmap, NN46205-103.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Copyright © 2008 Nortel Networks

.

Содержание Passport 8600 Series









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды