Nortel Passport 8600 Series Скачать руководство пользователя страница 48

Страница: 48 / 136

Initial steps using the CLI

Save the boot configuration.

Reboot the switch.

--End--

Variable definitions

Use the data in the following table to use the

config bootconfig sio

command.

Variable

Value

8databits <true|false>

Specifies either 8 (true) or 7 (false)
data bits for each byte for software to
interpret. The default is false.

baud <rate>

Configures the baud rate for the port.
The default is 9600.

enable <true|false>

Enables or disables the port. The
default is true.

info

Displays information about the
specified port.

mode <ascii|slip|ppp>

Configures the communication
mode for the serial port. The default
is American Standard Code for
Information Interchange (ASCII).

If you are configuring the modem
port, you can configure the
port to use the SLIP or the PPP
communication mode.

mtu <bytes>

Configures the size of the maximum
transmission unit for a PPP link
(0–2048). The default is zero.

my-ip <ipaddr>

Configures the IP address for the
server side, the Nortel Ethernet
Routing Switch 8600, of the
point-to-point link. The default is
0.0.0.0. Nortel recommends that you
use the current IP address for the
management port.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Содержание Passport 8600 Series

































































































































Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды

Nortel Passport 8600 Series, Пусконаладка

Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды