Nortel Passport 8600 Series Скачать руководство пользователя страница 58

Страница: 58 / 136

Initial steps using the CLI

Table 9
Job aid: Setup utility prompt descriptions (cont’d.)

Prompt

Description and action

Do you want to enable
TELNET [n] (y/n)?

Description: Specifies if you want to access
the switch by Telnet.

Action: Enter

to enable Telnet. Accept the

default (

) to not enable Telnet.

Do you want to enable TFTP
[n] (y/n)?

Description: Specifies if you want to access
the switch by Trivial FTP (TFTP).

Action: Enter

to enable TFTP. Accept the

default (

) to not enable TFTP.

Do you want to enable WEB
server service [n] (y/n)?

Description: Specifies if you want to enable
Web server service. Use the Web server
service to monitor statistics for the switch with
your Web browser.

Action: Enter

to enable Web server

service. Accept the default (

) to not enable

Web server service.

IP Address for mgmt port in
first CPU Slot [192.168.168.16
8/255.255.2.55.0]:

Description: Indicates the IP address for the
management port in the CPU slot you specify.

Action: Type the IP address of the
management port in the first CPU slot.

IP Address for mgmt port in
second CPU Slot [192.168.168
.169/255.255.255.0]:

Description: Indicates the IP address for the
management port in the CPU slot you specify.

Action: Type the IP address of the
management port in the second CPU slot.

IP Address for mgmt-virtual-ip
[0.0.0.0/0.0.0.0]:

Description: Indicates the IP address for the
virtual management port.

Action: Type the IP address of the virtual
management port. Accept the default
(0.0.0.0/0.0.0.0) to not specify an IP address.

Nortel Ethernet Routing Switch 8600

Commissioning

NN46205-319

01.01

Standard

30 May 2008

Содержание Passport 8600 Series

































































































































Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды

Nortel Passport 8600 Series, Пусконаладка

Результаты поиска

Содержание Passport 8600 Series

Отзывы:

Бренды по названию

Популярные бренды