Nordson LA 404 Скачать руководство пользователя страница 24

Страница: 24 / 73

LA 404 Pattern Control System

Part 1037527

200

Nordson Corporation

Manual 66-LA404-MA-01

Installation

This section provides pattern controller positioning information and basic
startup instructions.

Pattern Controller Ship-With Kit

The following contents are included in the pattern controller ship-with kit:

Kit Contents

Quantity

Fuses

Mounting bracket

Remote input plug

115 V line cord

Manual

Unpacking and Positioning the Pattern Controller

1. Exercise care to prevent equipment damage during unpacking.

2. Inspect for any damage that may have occurred during shipping. Report

any damage to the Nordson representative.

3. Bolt each mounting bracket (included in the pattern controller ship-with

kit) on either side of the pattern controller firmly.

4. Position the pattern controller close to the production line.

WARNING:

Equipment must be properly grounded and fused according to

its rated current consumption (see ID plate). Failure to follow the safety
procedures can result in serious injury.

5. Connect the pattern controller power cord to a properly grounded wall

outlet.

NOTE:

This pattern controller accepts a 115 V (included in the ship-with

kit) or a 230 V line cord. If a 230 V line cord is used, it will need to be
supplied by the user.

Содержание LA 404










































































Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды

Nordson LA 404, Руководство пользователя по изделию

Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды