Nordson LA 404 Скачать руководство пользователя страница 49

Страница: 49 / 73

LA 404 Pattern Control System

Part 1037527

200

Nordson Corporation

Manual 66-LA404-MA-01

Programs (1 – 50)

This setup menu screen can be used to save and recall any of the 50
programs, as well as copy one channel to another.

456

5=A!@1

+=I?!=K!!!!!!!@1!

!!!!!!!#6

,?9=FF!!!!!!!!@@!!!!!!!!!#6

G6>S!GV1!!!!:6!!!GV1!!!!!#6

6640023A

1. To save a program:

a. Press the

button for the cursor to appear beside the program

number.

b. Press the

button to select the desired program from 01 – 50.

c. Press the

button for the cursor to appear beside No.

d. Press the

button to change No to Yes, and this will save or

recall the desired program.

2. To recall a program:

a. Press the

button for the cursor to appear beside the program

number.

b. Press the

button to select the desired program from 01 – 50.

c. Press the

button for the cursor to appear beside No.

d. Press the

button to change No to Yes, and this will save or

recall the desired program.

3. To copy a channel to another channel:

a. Press the CHANNEL SELECT button on the front panel of the patten

controller to select a channel number (Copy CH1 – 4) whose
settings you would like to copy to another channel number.

b. Press the

button for the cursor to appear beside CH1.

c. Press the

button to go from CH2 – CH4.

d. Press the

button for the cursor to appear beside No.

e. Press the

button to change No to Yes, and this will copy the

channel settings.

NOTE:

The copy CH1 feature copies the channel data and setup

parameters (like delay, duration, bead type, and trigger assignment) from
the source channel to the destination channel.

Содержание LA 404










































































Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды

Nordson LA 404, Руководство пользователя по изделию

Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды