Nordson LA 404 Скачать руководство пользователя страница 45

Страница: 45 / 73

LA 404 Pattern Control System

Part 1037527

200

Nordson Corporation

Manual 66-LA404-MA-01

3. To set the activation speed (normal):

a. Press the

button for the cursor to appear beside the numeric

value.

b. Press the

button to set the desired normal value from

0 – 600 m/min.

NOTE:

The normal setting is used to enter the activation speed. Below

this speed, the normal bead pattern is broken into dots.

4. After setting Time, Pitch, and Normal, press the SET UP forward button

to open the Dly/Dur setup menu screen, refer to

Normal Beads

5. To set Dly:

a. Press the

button for the cursor to appear beside the numeric

value.

b. Press the

button to to set the desired delay value from

0 – 8187 mm.

6. To set Dur:

a. Press the

button for the cursor to appear beside the numeric

value.

b. Press the

button to set the desired duration value from

0 – 8192 mm.

Содержание LA 404










































































Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды

Nordson LA 404, Руководство пользователя по изделию

Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды