Nordson LA 404 Скачать руководство пользователя страница 29

Страница: 29 / 73

LA 404 Pattern Control System

Part 1037527

200

Nordson Corporation

Manual 66-LA404-MA-01

System Setup

The pattern controller can be customized with several setup options by
using the

Administrator

or the

Normal

operating modes. Refer to the

Quick

Programming Guide

for the sequence of menu screens that are used to

program the pattern controller.

Administrator Mode

Use the Administrator mode to setup the pattern controller for the first time:

1. While holding both the

and

buttons, turn on the power switch

located at the rear panel of the pattern controller.

2. Continue holding the

and

buttons until the words

Initializing

Administrator

, along with the panel and engine software versions appear

on the setup menu screen. Once this information appears, release the
buttons.

NOTE:

The pattern controller will perform a brief initializing procedure

which includes a self-diagnostic and preparation program. This
procedure takes between 10 – 15 seconds to complete.

!"#"$"%&"'"#(
%)*"#"+$,%$-,

./0/1!!!!!!!!!!!!!!!!./023

6640008A

CAUTION:

If the SET UP buttons are pressed inadvertently instead of the

and

buttons, the pattern controller will default to factory settings and

the current user settings will be lost.

3. Press the SET UP forward button to access each setup screen.

Содержание LA 404










































































Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды

Nordson LA 404, Руководство пользователя по изделию

Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды