Nordson LA 404 Скачать руководство пользователя страница 39

Страница: 39 / 73

LA 404 Pattern Control System

Part 1037527

200

Nordson Corporation

Manual 66-LA404-MA-01

Continuous Beads

When this bead type is selected, the outputs are activated if the line speed
is above the start speed, and deactivated if the line speed drops below the
stop speed. With continuous gluing no pattern is programmed, and no
trigger signal is required.

NOTE:

Low Speed Settings will override the line speed settings for

continuous bead patterns.

G6<:;<868K!R?=7

+:=5:

!T!ABA;<!

+:6>

!T!ABA;<

6640017A

1. To set start:

a. Press the

button for the cursor to appear beside the numeric

value.

b. Press the

button to to set the desired start value from

0 – 600 m/min.

2. To set stop:

a. Press the

button for the cursor to appear beside the numeric

value.

b. Press the

button to set the desired stop value from

0 – 600 m/min.

Содержание LA 404










































































Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды

Nordson LA 404, Руководство пользователя по изделию

Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды