Nordson LA 404 Скачать руководство пользователя страница 61

Страница: 61 / 73

LA 404 Pattern Control System

Part 1037527

200

Nordson Corporation

Manual 66-LA404-MA-01

Normal Mode

Use the Normal mode for daily operation of the pattern controller. In this
mode only the following screens can be accessed:

Production Data

Trigger Assignment

Trigger Settings

Pressure 1 and 2 Settings

Channel Compensation

Bead Type

Program

Warnings

Refer to the

Quick Programming Guide

for the sequence of menu screens

that are used to program the pattern controller.

1. Turn on the power switch located at the rear panel of the pattern

controller.

2. The pattern controller will perform a brief initializing procedure that

includes a self-diagnostic and preparation program.

The words

Initializing

, along with the panel and engine software versions

appear on the setup menu screen. Initializing takes between 10 – 15
seconds to complete.

"#"$"%&"'"#(

6640034A

./0/1!!!!!!!!!!!!!!!!./023

3. Press the SET UP button to access each setup screen.

NOTE:

The system can be powered down at any time and all

information will be saved.

Содержание LA 404










































































Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды

Nordson LA 404, Руководство пользователя по изделию

Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды