Nordson LA 404 Скачать руководство пользователя страница 19

Страница: 19 / 73

LA 404 Pattern Control System

Part 1037527

200

Nordson Corporation

Manual 66-LA404-MA-01

Front Panel

The front panel is used for entering and displaying the user inputs, and
transmitting the inputs to the pattern generation engine.

6640002A

Figure 3

Location of Front Panel Controls and Indicators

Item

Controls and Indicator

Description

Right arrow or Left arrow

Selects the item being programmed by moving up or down.

STAND BY

Enables and disables the gun output. When active (amber LED) disables

all channels. When inactive (green LED) all channels are permitted to run.

Up (increase) arrow or
Down (decrease) arrow

Increases or decreases the value of the selected parameter.

OUTPUT 1–4 LEDs

Illuminates when the selected gun output is activated.

CHANNEL SELECT

Selects which channel is being programmed, observed, or adjusted.

ENCODER LED

Illuminates with each pulse from the encoder.

TRIGGER LED

Illuminates when the selected trigger is On.

CHANNEL 1–4 LEDs

Illuminates to indicate that the selected channel is being programmed,

observed, or adjusted. The LEDs blink to indicate a warning condition.

PURGE

Activates all outputs for active channel only.

NOTE

: In flush mode it acts as an On/Off button. In purge mode it is a

momentary contact that is On when pressed and Off when released.

SET UP backward

Scrolls backward through the setup screens.

SET UP forward

Scrolls forward through the setup screens.

Setup menu screen

Alphanumeric, 9.22 mm character height, with a 4 x 20 backlight LCD.

–

Cursor or asterisk (

)

Appears beside a parameter to indicate that it is ready for setup.

Содержание LA 404










































































Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды

Nordson LA 404, Руководство пользователя по изделию

Результаты поиска

Содержание LA 404

Отзывы:

Похожие инструкции для LA 404

Бренды по названию

Популярные бренды