nord NORDAC FLEX SK 2 E-111-123-A Series, Руководство пользователя

Страница: 233 / 284

6 Operating status messages
BU 0200 en-US-4920 233
Pos : 696 /Anleit ungen/El ektr onik /FU und St art er/6. M eldung en zum Betriebsz ust and/Mel dungen Eins chalts perre (T abellenüberschrif t) @ 3\m od_1361803467385_14638.docx @ 59942 @ 5 @ 1
Notifications switch-on block, "not ready"
Display in the
SimpleBox /
ControlBox
Reason:
Text in the ParameterBox
Cause
• Remedy
Group Details in
P700 [-03]
Pos : 697 /Anleit ungen/El ektr onik /FU und St art er/6. M eldung en zum Betriebsz ust and/Störm eldung en (Auflist ung)/I nf ormation I 000_01 [SK 180E . .. SK 5x xE/SK 500P] @ 2\mod_1347457775195_14638. doc x @ 47348 @ @ 1
I000 0.1 Disable voltage from IO
If the "disable voltage" function is parameterized, input
(P420/P480) is Low
• "Set high" input
• Check signal cable (broken cable)
0.2 IO fast stop If the function "fast stop" is parameterized, input
(P420/P480) is at low
• "Set high" input
• Check signal cable (broken cable)
0.3 Block voltage from bus • Bus operation (P509): control word bit 1 is "low"
0.4 Bus fast stop • Bus operation (P509): control word bit 2 is "low"
0.5 Enable on start Enable signal (control word, Dig I/O or Bus I/O) was already
applied during the initialization phase (after line power "ON",
or control voltage "ON"). Or electrical phase is lacking.
• Only issue enable signal after completion of
initialization (i.e. when the VFD is ready)
• Activation of "Automatic Start" (P428)
0.6 – 0.7 Reserved Information message for PLC

see supplementary
instructions
Pos : 698 /Anleit ungen/El ektr onik /FU und St art er/6. M eldung en zum Betriebsz ust and/Störm eldung en (Auflist ung)/I nf ormation I 000_02-Erg änz ung 08 und 09 [ SK 180E ... SK 5xx E/ SK 500P] @ 10\mod_1455725649528_14638. docx @ 306333 @ @ 1
0.8 Right direction blocked Switch-on block with inverter shut-off activated by:
P540 or by "Enable right block" (P420 = 31, 73) or "Enable
left block" ( P420 = 32, 74),
The variable frequency drive switches to "Ready for
switching on" status
0.9 Left direction blocked
Pos : 699 /Anleit ungen/El ektr onik /FU und St art er/6. M eldung en zum Betriebsz ust and/Störm eldung en (Auflist ung)/I nf ormation I 006 [SK 180E . .. SK 5xxE, auß er SK 500P] @ 2\m od_1347457929759_14638. docx @ 47373 @ @ 1
I006
1)
6.0 Charging error Charging relay not energized, because:
• Line/DC link voltage too low
• Line voltage failure
• Evacuation run active ((P420)/(P480))
Pos : 700 /Anleit ungen/El ektr onik /FU und St art er/6. M eldung en zum Betriebsz ust and/Störm eldung en (Auflist ung)/I nf ormation I 011 [SK 180E . .. SK 5xxE/SK 500P] @ 2\mod_1347457936856_14638. docx @ 47398 @ @ 1
I011 11.0 Analog Stop If an analog input of the variable frequency drive or a
connected IO extension is configured to detect cable breaks
(2-10 V signal or 4-20 mA signal), the variable frequency
drive switches to the status "ready for switch-on" if the
analog signal undershoots the value
1 V or 2 mA
This also occurs if the relevant analog input is
parameterized to function "0" ("no function").
• Check connection
Pos : 701 /Anleit ungen/El ektr onik /FU und St art er/6. M eldung en zum Betriebsz ust and/Störm eldung en (Auflist ung)/I nf ormation I 014 "res erviert" [SK 200E . .. SK 5xxE/ SK 500P] @ 2\m od_1347457944329_14638. docx @ 47423 @ @ 1
I014
1)
14.4 Reserved Information message for POSICON

see supplementary
manual
Pos : 702 /Anleit ungen/El ektr onik /FU und St art er/6. M eldung en zum Betriebsz ust and/Störm eldung en (Auflist ung)/I nf ormation I 018 "res erviert" [SK 2xx E/ SK 5xxE/ SK 2xx E-FDS/SK 500P] @ 2\m od_1347457946544_14638. docx @ 47448 @ @ 1
I018
1)
18.0 Reserved Information message for "Safe stop" function

see
supplementary manual
Pos : 703 /Anleit ungen/El ektr onik /FU und St art er/6. M eldung en zum Betriebsz ust and/Störm eldung en (Auflist ung)/I nf ormation - Kennzeic hnung "Nic ht ber eit" @ 20\mod_1513067472948_14638.docx @ 2375119 @ @ 1
1) Indication of operating mode (message) on the
Parameter Box
or virtual operating unit of the
NORD CON-Software
: "Not ready"
Pos : 705 /Anleit ungen/El ektr onik /FU und St art er/6. M eldung en zum Betriebsz ust and/FAQ Betriebsst örungen @ 9\mod_1448963314277_14638. doc x @ 268441 @ 2 @ 1