nord NORDAC FLEX SK 2 E-111-123-A Series, Руководство пользователя

Страница: 203 / 284

5 Parameter
BU 0200 en-US-4920 203
Pos : 543 /Anleit ungen/El ektr onik /FU und St art er/5. Par ameter/ Par ameter auflist ung (P000 .. .)/P500- P599/Param et er P546 – Funk tion Bus- Sollw erte [ SK 1x 0E, SK 2xx E, SK 2xx E-FDS] @ 2\m od_1346932172150_14638.docx @ 43340 @ @ 1
P546
[-01]
...
[-03]
Function bus-setpoint
(bus setpoint function)
S P
0 ... 36
{ [-01] = 1 }
{ [-02] = 0 }
{ [-03] = 0 }
In this parameter, a function is allocated to the output setpoint during bus actuation.
NOTE: For further details, please refer to the relevant bus manual or the description for
(P400). (Values from 0% … 100% correspond to 0000
hex
… 4000
hex
,)
For standardization of the setpoint values: (please see chapter 8.9 "Standardization
of setpoint/target values").
[-01] = Bus-setpoint 1 [-02] = Bus-setpoint 2 [-03] = Bus-setpoint 3
Possible values which can be set:
0 =
Off
13 =
Current limit,
"Current limited"
1 =
Setpoint frequency (16 bit)
14 =
Current limit off
"Current switch-off limit"
2 =
Frequency addition
3 =
Frequency subtraction
15 =
Ramp time, (P102/103)
4 =
Minimum frequency
16 =
Pre-tension Torque, ((P214) multiplication)
5 =
Maximum frequency
17 =
Multiplication
6 =
Current value process control
18 =
Curve control
7 =
Nom. Val. Process ctrl.
19 =
Servo-mode Torque
8 =
Pl current frequency
20 =
BusIO InBits 0-7
9 =
PI ltd. Current freq.
21 =
...25 reserved, POSICON
10 =
PI supervised current freq.
31 =
Digital output IOE, sets the state of DOUT of
the first IOE
11 =
Torque current limit,
"Torque
current limited"
32 =
Analog output IOE, sets the value AOUT of the
first IOE), condition: P418 = Function "31"
Value must be between 0 and 100 (0hex and
64hex). Otherwise the minimum value is
output at the analog output.
12 =
Torque current limit off,
"Torque current switch-off limit"
Pos : 544 /Anleit ungen/El ektr onik /FU und St art er/5. Par ameter/ Par ameter auflist ung (P000 .. .)/P500- P599/Param et er P546 – Funk tion Bus- Sollw erte_Ergänz ung [ SK 2xx E, SK 2xx E-FDS] @ 19\m od_1506006002157_14638. docx @ 2366072 @ @ 1
33 =
Nom. Val. torque process ctrl.,
"Setpoint
torque process controller"
34 =
d-corr. F process
35 =
d-corr. Torque
36 =
d-corr. F+Torque
Pos : 545 /Anleit ungen/El ektr onik /FU und St art er/5. Par ameter/ Par ameter auflist ung (P000 .. .)/P500- P599/Param et er P549 – Funk tion Poti- Box [ SK 1x 0E, SK 2x xE, SK 2xx E-FDS] @ 2\mod_1346932172758_14638.docx @ 43364 @ @ 1
P549
Potentiometer Box function
(Potentiometer Box function)
S
0 ... 16
{ 0 }
This parameter provides the possibility of adding a correction value (fixed frequency, analog, bus)
to the current setpoint value by means of the Simple Box/Parameter Box keyboard.
The adjustment range is determined by the auxiliary setpoint value P410/411.
0 = Off 2 = Frequency addition
1 = Setpoint frequency
, with(P509)≠ 1
control via USS is possible
3 = Frequency subtraction
Pos : 546 /Allgem ein/ Allgem eingültig e Module/---------Seitenumbr uc h k ompakt --------- @ 13\m od_1476369695906_0. doc x @ 2265496 @ @ 1