Niveo NGSM48T2 Скачать руководство пользователя страница 309

Страница: 309 / 355

Chapter 5: Monitor, Diagnostic, Maintenance

Monitor, Diagnostic, Maintenance

NGSM48T2 User Manual | 309

Loop Protection

This page displays the loop protection port status the ports of the switch.

Loop protection port status is:

Port

The switch port number of the logical port.

Action

The currently configured port action.

Transmit

The currently configured port transmit mode.

Loops

The number of loops detected on this port.

Status

The current loop protection status of the port.

Loop

Whether a loop is currently detected on the port.

Time of Last Loop

The time of the last loop event detected.

Buttons

Refresh:

Click to refresh the page immediately.

Auto-refresh:

Check this box to enable an automatic refresh of the page at regular

intervals.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды