Niveo NGSM48T2 Скачать руководство пользователя страница 304

Страница: 304 / 355

Chapter 5: Monitor, Diagnostic, Maintenance

Monitor, Diagnostic, Maintenance

NGSM48T2 User Manual | 304

RMON Alarm Overview

This page provides an overview of RMON alarm entries.

The displayed fields are:

Indicates the index of Alarm control entry.

Interval

Indicates the interval in seconds for sampling and comparing the rising and falling

threshold.

Variable

Indicates the particular variable to be sampled

Sample Type

The method of sampling the selected variable and calculating the value to be

compared against the thresholds, posible sample types are:

Rising Threshold

Rising threshold value.

Rising Index

Rising event index.

Falling Threshold

Falling threshold value.

Falling Index

Falling event index.

Buttons

Refresh:

Click to refresh the page immediately.

Auto-refresh:

Click this box to enable an automatic refresh of the page at regular

intervals.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Бренды по названию

Популярные бренды