Niveo NGSM48T2 Скачать руководство пользователя страница 282

Страница: 282 / 355

Chapter 5: Monitor, Diagnostic, Maintenance

Monitor, Diagnostic, Maintenance

NGSM48T2 User Manual | 282

Last Authentication

Shows the date and time of the last authentication of the client (successful as well as

unsuccessful).

Buttons

The port select box determines which port is affected when clicking the buttons.

Auto-refresh

Check this box to enable an automatic refresh of the page at regular intervals.

Click to refresh the page immediately.

This button is available in the following modes:



Force Authorized



Force Unauthorized



Port-based 802.1X



Single 802.1X

Click to clear the counters for the selected port.

This button is available in the following modes:



Multi 802.1X



MAC-based Auth.X

Click to clear both the port counters and all of the attached client's counters. The

"Last Client" will not be cleared, however.

This button is available in the following modes:



Multi 802.1X



MAC-based Auth.X

Click to clear only the currently selected client's counters.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды