Niveo NGSM48T2 Скачать руководство пользователя страница 176

Страница: 176 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 176

Egress

Port Egress Rewriting can be one of -

Disabled:

No Egress rewrite.

Enable:

Rewrite

enabled

without remapping.

Remap DP Unaware:

DSCP from analyzer is remapped and frame is remarked with

remapped DSCP value. The remapped DSCP value is always taken from the 'DSCP

Translation->Egress Remap DP0' table.

Remap DP Aware:

DSCP from

analyzer

is remapped and frame is remarked with

remapped DSCP value. Depending on the DP level of the frame, the remapped

DSCP value is either taken from the 'DSCP Translation->Egress Remap DP0' table

or from the 'DSCP Translation->Egress Remap DP1' table.

Buttons

Save:

Click to save changes.

Reset:

Click to undo any changes made locally and revert to previously saved

values.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды