Niveo NGSM48T2 Скачать руководство пользователя страница 114

Страница: 114 / 355

Chapter 3: Featuring Configuration

– Web UI

Featuring Configuration

– Web UI

NGSM48T2 User Manual | 114

Port Configuration

Port

The switch port number of the port.

Enable

Controls whether loop protection is enabled on this switch port.

Action

Configures the action performed when a loop is detected on a port. The valid values

are:

Shutdown Port:

Shutdown the port until the Shutdown Time timeout.

Shutdown Port and Log:

Shutdown the port and log the status.

Log Only:

Only log the status.

Tx Mode

Controls whether the port is actively generating loop protection PDU's, or whether it

is just passively looking for looped PDU's.

Button

Save:

Click to save changes.

Reset:

Click to undo any changes made locally and revert to previously saved

values.

Содержание NGSM48T2




































































































































































































































































































































































Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды

Niveo NGSM48T2, Руководство пользователя

Результаты поиска

Содержание NGSM48T2

Отзывы:

Похожие инструкции для NGSM48T2

Бренды по названию

Популярные бренды